
How to Deflate Intex Air Mattress?
Assuming you would like tips on how to quickly and easily deflate an Intex air mattress:
Intex air mattresses are popular for their affordability and portability. They are ideal for camping trips or overnight guests, but can be a pain to deflate.
Here are a few tips on how to quickly and easily deflate your Intex air mattress.
Deflating Intex Airbed part 2| #121
- Take the mattress out of the packaging and find the small black valve on the side
- Unscrew the cap from the valve and insert the end of a straw into the hole
- Blow into the straw until you feel resistance, then remove the straw and screw the cap back onto the valve
- The mattress will start to deflate on its own
- Once it’s mostly flat, fold it in half lengthwise and roll it up tightly
Intex Air Mattress Won’T Deflate
An air mattress is a great way to get a comfortable night’s sleep when you’re away from home. But what do you do when your Intex air mattress won’t deflate?
There are a few things that could be causing your air mattress to fail to deflate.
The most common problem is that the valve is not completely closed. Make sure that the valve is turned all the way to the “off” position.
Another possibility is that there is a hole in the mattress.
Inspect the entire surface of the mattress for any holes or punctures. If you find one, patch it up with a repair kit or some duct tape.
If neither of these solutions work, then you may need to replace the pump.
Check to see if your warranty covers pump replacement – if so, contact Intex customer service for assistance. Otherwise, you can purchase a new pump at an online retailer or sporting goods store.
How to Deflate Intex Air Mattress With Hand Pump
Assuming you have an Intex air mattress with a hand pump, here are detailed instructions on how to deflate it:
1. Start by disconnecting the inflation hose from the valve stem. If there’s a cap over the valve stem, unscrew it as well.
2. Once the inflation hose is disconnected, hold the end of the deflation tube (the part that goes into the mattress) over a garbage can or other open container.
3. Open up the valve stem by turning it counterclockwise until it’s fully open. You should hear air rushing out of the mattress and into the deflation tube.
Keep holding onto the deflation tube until most of the air has been released from the mattress – this could take a minute or two depending on how much air was in the mattress to begin with.
4. Close off the valve stem by turning it clockwise until it’s tight, then re-connect the inflation hose (if applicable). Screw on any caps that were removed earlier.
How to Deflate an Intex Air Mattress Without a Pump
Inflating and deflating an air mattress is easy with the right tools. If you don’t have a pump, you can still deflate your Intex air mattress without one. Here’s how:
1. Open the valve on your air mattress. This will allow the air to start escaping.
2. Fold the mattress in half so that all of the air is concentrated in one area.
3. Sit on the edge of the mattress and roll it up tightly, pressing out as much air as possible as you go.
4. Once it’s rolled up, tie or clip the end shut to keep all of the air inside.
5. Unroll the mattress and open the valve again to release any remaining air.
How to Deflate an Air Mattress With a Built-In Pump
Assuming you would like a blog post titled “How to Deflate an Air Mattress With a Built-In Pump”:
If you have an air mattress with a built-in pump, deflating it is easy. Just follow these simple steps and you’ll have your mattress packed up in no time.
First, make sure that the valve on the air mattress is in the closed position. This will prevent any air from escaping as you’re deflating the mattress.
Next, locate the deflation port on the mattress.
It should be located near the pump. Once you’ve found it, insert the deflation nozzle into the port and turn on the pump.
The pump will start to draw air out of the mattress and it will begin to collapse.
Once it’s completely flat, close off the deflation port and remove the nozzle. Your mattress is now ready to be stored away!
How to Deflate Air Mattress Without Pump
Assuming you don’t have a pump and need to deflate your air mattress, there are a few ways you can go about doing it. One way is to use the valve on the mattress to let out the air little by little. This method will take some time, but eventually all the air will be out of the mattress.
Another way is to roll up the mattress from one end until all the air is forced out. This method may be quicker than using the valve, but it requires some effort on your part.
Once all the air is out of your mattress, be sure to store it in a cool, dry place until you’re ready to use it again.

Credit: krostrade.com
How Do I Deflate Intex Quick Fill?
If you have an Intex quick fill air mattress, you may be wondering how to deflate it. Here are some simple instructions:
1. First, remove the cap from the valve.
2. Next, use a small amount of pressure to push on the black tab inside the valve (this will open up the valve and allow air to escape).
3. Once the mattress is fully deflated, replace the cap on the valve and store your mattress until next time!
How Do You Deflate an Air Mattress With a Built in Foot Pump?
An air mattress with a built in foot pump can be deflated by following these steps:
1. Remove the cap from the valve at the bottom of the mattress.
2. Insert the deflation nozzle of the pump into the valve.
3. Pump air out of the mattress until it is fully deflated.
4. Remove the deflation nozzle from the valve and replace the cap.
How Do You Close an Intex Air Mattress Valve?
Assuming you are talking about the valve that lets air in and out: There should be a knob or handle on the outside of the valve. Turn it to the right to close it (clockwise).
Conclusion
Most people don’t know how to properly deflate an Intex air mattress. Here are easy instructions:
First, remove the air plug from the mattress.
Next, fold the mattress in half so that all of the air is forced out. Once it is folded, roll it up tightly and store it in a cool, dry place.

